UTV PR-100 Production
Limited UTV 2000 CC Normally Aspirated
* Updated January 28th, 2022 *
Click here to download a PDF.
Two seat vehicles built using a production UTV. Any manufacture UTV may be used providing the model used has been series produced in a minimum of 1000 units within a twelve (12) month period. Maximum engine size 2000cc. Stock production body parts required.
Entrants in this class shall comply with all applicable general regulations.
This class is a Stock Production class, and all components will be considered Stock Production unless unrestricted herein. If it does not say it can be removed, replaced, or modified it has to remain stock as delivered by the manufacturer of the vehicle.
Manufactures body, engine, transmission, chassis, suspension, and drive train components must be retained.
NOTE: The UTR abbreviations listed under this class (I.E. UTR1 HELMETS) refer to UTR cross reference listings in the front of this book. These UTR cross-referenced listings are part of the class rules. Where a conflict occurs between the UTR cross-referenced listing and a rule contained under this class, the rule contained under this class takes priority.
UTR2 PROTECTIVE CLOTHING
UTR3 EYE PROTECTION and DENTURES
UTR4 HEAD AND NECK RESTRAINTS
UTR5 FIRST AID KIT
UTR6 EMERGENCY SIGNALING DEVICES
UTR9 FIRE SUPPRESSION EQUIPMENT
UTR10 SURVIVAL SUPPLIES
UTR11 SHOCK ABSORBERS and BUMP STOPS
Any shock in stock location is allowed.
Springs may be of any size and manufacture.
UTR12 SECONDARY SUSPENSION
No secondary suspension allowed.
UTR13 WHEELS and TIRES
Wheel diameter is fifteen (15) inch maximum.
Maximum tire size is 35×12.5×15.
STEERING and BRAKE COMPONENTS
All batteries must be securely mounted. Battery shut off switch is required.
All vehicles must have a minimum of two (2) taillights and two (2) brake lights. Tail and brake lights must be 3 inch in diameter. All UTV’s must also have four (4) additional rear facing safety lights. One (1) solid amber, one (1) flashing amber, one (1) solid blue, and one (1) flashing blue. All safety lights must be LED with a minimum of 2000 lumens output. All safety lights must be wired directly to the battery switch. All lights must be mounted 48 inches from the ground minimum. Safety lights must be on at all times. Vehicles without working safety lights will not be allowed to leave the starting line or pass through a check point. All lights subject to M400 approval.
UTR22 FUEL TANKS
UTR23 FUEL FILLERS LINES, VENTS, and CAPS
Stock tank in stock location or Fuel cell in any location.
ENGINE, TRANSMISSION and DRIVELINES
UTR24 ENGINE and ENGINE DISPLACEMENT
Maximum engine displacement is 2000cc.
Engine must remain stock as delivered by the manufacture.
No engine parts may be modified or replaced.
Clutch housing cooling inlet and outlet tubes (snorkels) maybe modified or replaced.
Any manufacturer air cleaner in stock housing is allowed.
UTR25 ENGINE REPLACEMENT
UTR29 DRIVE SHAFTS
UTR30 FLYWHEEL SHIELDS
UTR31 FLUID COOLERS
UTR32 AUXILIARY EQUIPMENT
UTR33 SUPERCHARGERS and TURBOCHARGERS
VEHICLE SAFETY EQUIPMENT
UTR34 ROLL CAGES
Stock production roll cages are not allowed.
UTR35 SAFETY HARNESS
UTR36 SAFETY NETS
Race seats only. All stock seats must be removed.
GENERAL VEHICLE COMPONENTS
UTR38 DRIVERS COMPARTMENT
UTR39 DOORS AND LATCHES
Doors must be securely closed.
UTR44 BUMPERS and HAZARDOUS PROTRUSIONS
Safe front and rear bumpers required. No shape corners or hazardous protrusions.
UTR46 SKID PLATES
UTR48 CHASSIS and BODY
Stock grill, hood, and front and rear fenders must be used.
Roof must be covered with sheet metal .060 thick minimum.
UTR50 IDENTIFICATION MARKINGS
M400 will assign race numbers.
UTR51 ADVERTISING on VEHICLES
UTR52 RADIO EQUIPMENT
UTR54 TRACKING DEVICE